Marlin? Ranger Model 34A .22 Rifle

This is an area for guests to post questions

Moderators: Regnier (gunrunner), JohnK, Sure-Shot, Marlin

Forum rules
I have unlocked this forum but made it read only for non members -- Webmaster --
User avatar
tigweld
Marksman
Posts: 140
Joined: Sat Jan 17, 2009 10:12 am
Location: Michigan

Marlin? Ranger Model 34A .22 Rifle

Post by tigweld »

I have a Ranger Model 34A .22 semi-auto rifle. Top of the barrel reads:
RANGER 22 LONG RIFLE-MODEL 34A
---MADE IN USA ---

Left side of barrel near rear sight area reads:
22 LONG RIFLE ONLY-SMOKELESS GREASE

It has a 24" barrel,walnut stock,plain steel buttplate and is clip fed.
Sorry to say,has no clip,front sight,bolt handle or extractor.

I believe this rifle is a "Store Brand" rifle that was made by Marlin from
what I could find on the internet.

Could you please tell me some more info on this rifle and possible source
of repair parts?

Thanks! tigweld
"Let there be Welders,to attach metal things to other metal things"
Regnier (gunrunner)
Distinguished Expert
Posts: 4667
Joined: Sun Oct 27, 2002 2:33 am
Location: The Sunflower State

Re: Marlin? Ranger Model 34A .22 Rifle

Post by Regnier (gunrunner) »

Tigweld;

Since the barrel of your Ranger Model 34A has the .22 Long Rfle Only-Smokeless Greased, it is the Marlin Model 50 as no other Marlin has the particular barrel stamping. That is the good news that it is identified. The bad news is that parts for the Model 50 are nearly impossible to find. At best, try Numrich Gun Parts Corporation as they do show some parts in the catalog for the Model 50. (http://www.e-gunparts.com) They list the magazine, but different reports say they do not work in the old Model 50.
Good luck..................
Due to the increasing cost of ammunition, there will be no warning shot!

The growing federal deficit = generational slavery to the national debt.

If the world was perfect.......it wouldn't be.
User avatar
tigweld
Marksman
Posts: 140
Joined: Sat Jan 17, 2009 10:12 am
Location: Michigan

Re: Marlin? Ranger Model 34A .22 Rifle

Post by tigweld »

Thanks for your reply!! :D
If interested in seeing, I do have some photos. It is set-up a little different than the Marlin Model 50 that I found photos of on this site. The safety is located at the rear of the receiver and the takedown screw is located in front of the clip opening.
Do you happen to know the years of production for this rifle and total production?

Thanks, tigweld
"Let there be Welders,to attach metal things to other metal things"
RounderRick
Beginner
Posts: 17
Joined: Thu Dec 18, 2008 10:22 am

Re: Marlin? Ranger Model 34A .22 Rifle

Post by RounderRick »

Hello tigweld – I guess what you’ve got then is an A1. Sears did some funny things with their model numbers, but generally all the Ranger marked rifles were pre-WW2. With the safety you described, that would be an early (or 1st variation) of the A1. A poster on another board has mentioned the magazines are available from Numrich, but years ago when I tried they were hard to come by. If you get one and it works good, please let us know. GoodLuck - RounderRick
User avatar
tigweld
Marksman
Posts: 140
Joined: Sat Jan 17, 2009 10:12 am
Location: Michigan

Re: Marlin? Ranger Model 34A .22 Rifle

Post by tigweld »

Hi RounderRick
Thanks for the additional info. :D This site has been a very BIG help.
Wish I could find some part drawings/blueprints, I would be able to fabricate
some of the parts I need.

tigweld
"Let there be Welders,to attach metal things to other metal things"
Regnier (gunrunner)
Distinguished Expert
Posts: 4667
Joined: Sun Oct 27, 2002 2:33 am
Location: The Sunflower State

Re: Marlin? Ranger Model 34A .22 Rifle

Post by Regnier (gunrunner) »

Tigweld;

I may be incorrect to say your rifle is the Marlin Model 50. The cross references I checked all said that the Ranger Model 34A was the Marlin Model 50. But, it is the A-1 that indeed does have that cartridge marking on the barrel.
Sorry for any confusion this may have caused.
Due to the increasing cost of ammunition, there will be no warning shot!

The growing federal deficit = generational slavery to the national debt.

If the world was perfect.......it wouldn't be.
User avatar
tigweld
Marksman
Posts: 140
Joined: Sat Jan 17, 2009 10:12 am
Location: Michigan

Re: Marlin? Ranger Model 34A .22 Rifle

Post by tigweld »

Gunrunner,

I have some photos now posted that might help out. If you go to
(http://www.pbase.com/tigweld/ranger34a_project) I have a gallery of five
photos with closeups of the rifle markings. Again ,Thanks for all
the help on this site.

tigweld
Last edited by tigweld on Sun Mar 01, 2009 7:59 pm, edited 3 times in total.
"Let there be Welders,to attach metal things to other metal things"
Regnier (gunrunner)
Distinguished Expert
Posts: 4667
Joined: Sun Oct 27, 2002 2:33 am
Location: The Sunflower State

Re: Marlin? Ranger Model 34A .22 Rifle

Post by Regnier (gunrunner) »

Tigweld;

Definitely the A-1.
Due to the increasing cost of ammunition, there will be no warning shot!

The growing federal deficit = generational slavery to the national debt.

If the world was perfect.......it wouldn't be.
User avatar
tigweld
Marksman
Posts: 140
Joined: Sat Jan 17, 2009 10:12 am
Location: Michigan

Re: Marlin? Ranger Model 34A .22 Rifle

Post by tigweld »

Gunrunner,

I just left four more photos at (http://www.pbase.com/tigweld/ranger34a_project) which might further help out with identification. A couple are of the barrel/action out of the
stock.
Do you happen to know how many rifles there were in the total production of
the A-1 series? The Model 50 series?
I did run across some photos of the Marlin Model 50 .22 on this site, and a guy
can see the differences between the A-1 and later Model 50.
Thanks again for all the help on this site :D

tigweld
Last edited by tigweld on Sat Mar 07, 2009 3:58 pm, edited 1 time in total.
"Let there be Welders,to attach metal things to other metal things"
Regnier (gunrunner)
Distinguished Expert
Posts: 4667
Joined: Sun Oct 27, 2002 2:33 am
Location: The Sunflower State

Re: Marlin? Ranger Model 34A .22 Rifle

Post by Regnier (gunrunner) »

Tigweld;

The Marlin Model 50 preceeded the Model A-1. The Model 50 was made from 1931 to 1935, and the A-1 came out in 1936. It was made in a couple of variations up to 1946. You have the first variation of the Model A-1.
There are no production records for many of the inexpensive Marlin's produced over the years. If you will look, you will see that your rifle has no serial number. It was not required for firearms to have serial numbers until after passage of the Gun Control Act of 1968.
I hope this helps.
Due to the increasing cost of ammunition, there will be no warning shot!

The growing federal deficit = generational slavery to the national debt.

If the world was perfect.......it wouldn't be.
User avatar
tigweld
Marksman
Posts: 140
Joined: Sat Jan 17, 2009 10:12 am
Location: Michigan

Re: Marlin? Ranger Model 34A .22 Rifle

Post by tigweld »

Gunrunner,

That clears up alot of my questions on this rifle. Sometime,with luck and a few parts
perhaps I can breathe life into the old Model A-1 alias Ranger Model 34A.

tigweld
"Let there be Welders,to attach metal things to other metal things"
Sure-Shot
Distinguished Expert
Posts: 1304
Joined: Sun Nov 17, 2002 5:01 pm
Location: Poulsbo, Washington, USA

Re: Marlin? Ranger Model 34A .22 Rifle

Post by Sure-Shot »

http://www.gun-parts.com/marlin/ There are some parts here.

Ask on other parts.....scarce.................
================
Marlin A-1 Automatic .22
A-1 Firing Pin................................$35
A-1 Extractor................................$25
A-1 Bolt handle.............................$25
Peep Sight A-1..............................$45
GBOT, GBUSA
Sure-Shot
Distinguished Expert
Posts: 1304
Joined: Sun Nov 17, 2002 5:01 pm
Location: Poulsbo, Washington, USA

Re: Marlin? Ranger Model 34A .22 Rifle

Post by Sure-Shot »

GBOT, GBUSA
User avatar
tigweld
Marksman
Posts: 140
Joined: Sat Jan 17, 2009 10:12 am
Location: Michigan

Re: Marlin? Ranger Model 34A .22 Rifle

Post by tigweld »

Sure-Shot,

Thanks! for the additional information on the A-1. It will really be a big help looking for parts.
In my area there will be a gun show in the end of February and I'll do some searching there for parts. If I do get it back in firing order,more photos to follow.

tigweld
"Let there be Welders,to attach metal things to other metal things"
User avatar
tigweld
Marksman
Posts: 140
Joined: Sat Jan 17, 2009 10:12 am
Location: Michigan

Re: Marlin? Ranger Model 34A .22 Rifle

Post by tigweld »

Well as promised,I'm posting an update on the 34A/A1. Thanks to Sure-Shot and the photo
he posted of the parts list for the A1,I was able to get an idea of what the bolt handle looked
like. With some rough dimensions and a little lathe work at the Tool & Die shop I work at, I made up a bolt handle. At (http://www.pbase.com/tigweld/ranger_34a_update) I posted some photos of the finished product. I'll order the rest of the parts I need in the next few weeks
and have the rifle back in firing order.
In case somebody wondered, I have over 30 years in the Tool & Die trade,15 years of that
welding full time. TIG,MIG,ARC,Oxy/Acetylene and Laser welding.

tigweld
"Let there be Welders,to attach metal things to other metal things"
Post Reply